Limited Offer Get 25% off — use code BESTW25
No AI No Plagiarism On-Time Delivery Free Revisions
Claim Now
Prices start at $5 per page · plagiarism-free papers · free revisions for 14 days 24/7 support: support@bestwriters.com
Uncategorized

Design and Operation of Sustainable Systems

  • Posted
  • Authoradmin
  • Length1,501 words
  • Reading time7 min
Write My Assignment FREE

Page 1 of 9
Academic Year 2019/20
Examination Period: SEMESTER 2 – Exam
Module Code: MP4701
Module CRN: 37227
Exam Type: Written
Module Title: Design and Operation of Sustainable Systems
Module Leader: Dr. Geng Feng

Examination Paper Structure
This examination paper has 5 questions in total.
There are no appendices.
All questions carry equal marks of 25 marks.
Students to be provided with:
None
Instructions to Students:
The time allowed to complete this examination paper is 24 hrs
Answer any Four questions. Each question is worth 25 marks. Total exam is out of
100 marks
The use of dictionaries is not permitted in this examination.
.

Page 2 of 9
Question 1: Condition Monitoring
a) What are the main steps in the generic procedure for implementing a condition monitoring
programme which are outlined in BS ISO 17359:2011?
(4 marks)
b) Answer the following about condition monitoring techniques, according to your experience
during the module:
1- With the aid of a block diagram, outline the main elements of a vibration analysis system
(2 marks)
2- Name two vibration analysis methods used to analysis vibration signals. (2 marks)
3- For the given accelerometer response (shown in the figure Q1.1): (2 marks)
i. At what approximate frequency does attenuation occur?
ii. What approximate frequency does resonance occur?
4- Name two sources of Acoustic Emission signal in machinery condition monitoring, and the
corresponding AE signal types.
(2 marks)
5- Name two approaches used in oil debris analysis. (2 marks)
c) For the gearbox (shown in Figure Q1.2), use the BS ISO 13373-3 standard (Equations provided
in Appendix A) to calculate the expected defect frequencies of bearings no. 6, if the input shaft

speed is 6000rpm.
Given:
(6 marks)

Gearbox Data: Type: Reduction Helical Gearbox.
No. of stages: 2
Figure Q1.1
Page 3 of 9
Bearings data: All bearings shown in Figure Q1.2 and Q1.3 are cylindrical roller bearings
and of the same type and have the data provided in Table Q1.
d) For Gear A in the helical gearbox shown in Figure Q1.2, calculate the expected gear
fundamental frequencies, if the input shaft speed is 6000 rpm. (5 marks)
TOTAL 25 marks

Stage Number of teeth
1st Gear A: 21 Gear B: 68
2nd Gear C: 30 Gear D: 48
Parameter
Table Q1, Bearing dimensions
mm
Outer diameter 62
Inner diameter 25
Pitch diameter of rollers (P) 44
Diameter of roller (B) 8
Number of rollers (N) 10
Contact angle (Ø) 0

B A
D C
Output
Input
Figure Q1.2, source www.skf.com
Figure Q1.3, source www.skf.com

Page 4 of 9
Question 2: Structural Health Monitoring
a) Identify the three main elements of a structural health monitoring system architecture for
an aircraft application. Provide examples of the typical systems or components to be
found in each element. (3 marks)
b) Describe three of the key benefits of structural health monitoring over current methods
used for inspecting and maintaining safety critical structures such as aircraft.
(3 marks)
c) Fibre optic sensors provide an alternative to electrical strain gauges for the measurement
of strain at multiple points on structures. One form of fibre optic sensor systems uses
Fibre Bragg Gratings (FBGs) as the strain sensing elements
I. Draw a diagram of a fibre optic sensor system that uses FBG as strain sensors.
Label each of the main components and describe briefly what function they fulfil.
(5 marks)
II. List the main advantages of fibre optic strain sensors when compared with
electrical strain gauges.
(3 marks)
d) An aircraft monitoring application requires strain measurements in the range
-3,500 microstrain (µε) to + 3,500 microstrain (µε) . The temperature range over which they
must operate is between -500 C and +1050 C
An FBG sensor system has the following characteristics for each FBG sensor:
Strain sensitivity, Δλ / ε = 1.2 pm / µε
Temperature sensitivity, Δλ / ΔT = 10 pm / 0C.
(pm = picometers)
I. To achieve the full strain measurement range of +/- 3,500 µε, at a constant
temperature calculate the wavelength bandwidth needed for each sensor (in units of
pm). (see Figure Q2.1). (5 Marks)
II. At a constant strain level, calculate the change in wavelength (in units of pm)
experienced by each FBG when subject to the full temperature range for the aircraft
application (see Figure Q2.1). (3 Marks)
III. Using the answers from I and II, If 5 FBG sensors are required in a single fibre
system calculate the minimum overall wavelength bandwidth of the system to
accommodate all 5 sensors ensuring there is no overlap between each sensor channel.
(see Figure Q2.2). (3 Marks)
Page 5 of 9
Figure Q2.1. Principle of a Fibre Bragg Grating (FBG) strain sensor. Each FBG sensor
reflects at a nominal peak wavelength. When the FBG experiences tensile strain and/or
temperature increase, the peak shifts to longer wavelengths. When subject to compressive
strain and/or decrease in temperature, the peak shifts to shorter wavelengths.
Figure Q2.2. Multiple FBGs arranged in a system showing each sensor channel.
TOTAL 25 marks
Page 6 of 9
Question 3: Qualitative Systems Reliability Analysis
a) FMEA and FTA are two key concepts to perform system reliability analysis. (i) What do the
letters stand for in the acronyms FMEA and FTA? (ii) State the advantages of an FMEA
process.
(6 marks)
b) A water turbine is a rotary machine that converts kinetic energy and potential energy of
water into mechanical work. It is mostly found in dams to generate electric power from water
kinetic energy, which is clean and renewable. Figure Q3 below shows the cut-away view of a
water turbine and electrical generator.
Figure Q3. Water turbine and electrical generator cut-away view
State two design for reliability principles according to British Standard and how they could be
applied to the wind turbine design.
(4 marks)
c) Perform an indicative 3-level system break down describing the water turbine and generator
system, identify ONLY 4 failure modes (at least two different modes for one component) and
perform FMEA to prioritise risks.
(15 marks)
TOTAL 25 marks
Page 7 of 9
Question 4: Quantitative System Reliability Analysis

a) Figure Q4.1 shows a Reliability Block Diagram with a number of components in series
and parallel. Components B1, B2 and B3 are identical and operate all the time. Only
one of the three components is required to be operational for the triplex sub- system to
operate. Hence it is referred to as a “1 out of 3” system.
Figure Q4.1. Reliability Block Diagram
Calculate the overall system reliability at T = 1500 hrs using the data in Table Q4.
Table Q4. Data for Figure Q4.1
(10 marks)
b) Comment on the answer you obtain (i.e. which part of the system influences the
overall reliability most)?
(2 marks)
c) What is the significance of operating components B1, B2 and B3 in parallel, comment
on the advantages and disadvantages of parallel system?
(3 marks)
d) Using an appropriate method, calculate the reliability of the Reliability Block Diagram
shown in Figure Q4.2? Show all steps of your working, and assume the reliability of
each component is 0.97.
Figure Q4.2. A system with five components.
(10 Marks)

TOTAL 25 marks
Page 8 of 9
Question 5: Bearings and Lubrication
a) A hard steel cone having a semi-angle of 85° is drawn across the surface of a soft bronze
plate by the mechanism of deformation due to ploughing. The plate has a hardness of
900 MPa, and the normal load is constant at 30 N.

(i) Estimate the width of the scratch, coefficient of friction and the volume of
material displaced in unit sliding distance.

(5 marks)
(ii) If the same hard steel cone slides against carbon steel with hardness 1200 MPa,
with the same load. Estimate the width of the scratch, coefficient of friction and the
volume of material displaced in unit sliding distance.
(5 marks)
b) Solvay, a manufacturing and engineering services company is specialized in the
production of automotive parts made of polymer and composite materials for high-end
vehicles. A design engineer in the Solvay Company is interested in evaluation of the
wear characteristic of the polyamide polymer using a pin-on-disc test apparatus as per
the ASTM standard G99. The design engineer is planning to expand the company
business in the design and manufacturing of the polymeric bearings for the automotive
and aerospace applications. In a wear test, a polyamide polymer pin having a diameter
of 25 mm is placed with its flat face resting on a smooth 304 stainless steel disc under
a normal load of 40 N. The central axis of the pin is at 80 mm from the central axis of
the disc. The disc is rotated about its axis at 300 rpm for 2000 hr (Table Q5). Calculate
the wear volume for the polyamide polymer and stainless steel material if the wear
coefficients are known for this tribological couple in these conditions. Justify the results
and suggest whether the polyamide is a good material to slide against stainless steel?
Table Q5: Material parameters

Material Hardness Density Wear coefficient
Polyamide polymer 220 MPa 1200 kg/m3 6.1 × 10-6
304 Stainless Steel 2700 MPa 7800 kg/m3 3.9 × 10-10

(8 marks)
c) Industrial rotating machinery relies upon rolling bearings to reduce friction, power
consumption and heat generation, while simultaneously supporting increasingly
heavier applied loads at higher speeds with a higher degree of accuracy. Bearings in
service can be prone to wear for many reasons, whether due to poor lubrication
conditions (associated with high temperatures and/or low lubricant viscosities), sudden
variations in load or speed, standstill vibration and/or particle or liquid contaminants.
All can lead to dramatically shorter bearing (and machinery) service life over time. SKF
bearing manufacturers want to increase the service life of cylindrical roller bearings by
surface treatment with the application of a hard, wear-resistant ceramic (Figure Q5).
Page 9 of 9
With the aid of diagrams, illustrate one technique by which this could be done, and
briefly describe the advantages and disadvantages of the techniques with respect to
tribological application.
Figure Q5. Cylindrical roller Bearing
(7 marks)
TOTAL 25 marks

The post Design and Operation of Sustainable Systems appeared first on My Assignment Online.

Plagiarism Free Assignment Help

Expert Help With This Assignment — On Your Terms

✓ Native UK, USA & Australia writers ✓ Deadline from 3 hours ✓ 100% Plagiarism-Free — Turnitin included ✓ Unlimited free revisions ✓ Free to submit — compare quotes

admin

Academic writer and editor at BestWriters.

Get your paper off your plate tonight

Post your instructions for free. Prices start at $5 per page.

Place an order