Limited Offer Get 25% off — use code BESTW25
No AI No Plagiarism On-Time Delivery Free Revisions
Claim Now
Prices start at $5 per page · plagiarism-free papers · free revisions for 14 days 24/7 support: support@bestwriters.com
Uncategorized

Design Assignment

  • Posted
  • Authoradmin
  • Length2,968 words
  • Reading time13 min
Write My Assignment FREE

Design
Assignment – 2020

You
are to design a small-scale industry plate rolling machine for
rolling any aluminium alloy 1xxx series. The rolling mill produces
aluminium sheets of width 400mm wide and 20mm from 25mm thick
aluminium stock. The roll radius is about 300mm, and the rolls rotate
at 100rpm. The tolerance in thickness should be 0.01mm.
You may need to roll the stock material several times to produce the
required thickness.

The
power for running this mill comes from a motor running at 1500rpm.

You
should design the gears that drive the rollers to run the mill. The
gap between the rollers should be adjustable up to about 10mm. The
gap between the rollers should be held tight by power screws driven
by a motor or a belt drive for adjusting the gap size. The roller
bearings that hold the rollers in place must be designed to ensure a
smooth operation. You must work out the torque needed to run the
rollers and size the electric motor accordingly. The bolts that are
needed to hold the rollers should be able to take the load
accordingly. A clutch/braking mechanism must be designed to stop the
machine after the rolling is completed.

The
rolling machine is cycled about 100 times a day and this means, you
must design for fatigue life of all the components involved. For
comfort of workers the noise should not exceed 60dB.

Detail
what material you will use and the welding, if any, must be clearly
listed.

Your
design should be carried out on a CAD package, such as CREO, and all
the calculations must be made using a spreadsheet software. The CAD
package should be capable of producing animation. The machine should
be shown in animation through the software package.

Your
design should consider sustainability, modularity, and
maintainability.

You
should reference appropriate standards when designing the machine
elements. You must also use readily-purchased components from the
market place.

Your
design should consist of a gear box, gear-shaft, keys and
keyways, bearings, welds, threaded fasteners, clutches and brakes,
couplings and springs. You must specify tolerances and design for
fatigue and surface fatigue. You must follow industry standards and
use, where possible, modular design.

Assumptions
should be reasonable and justified.

You
should also produce a 3D printed part of the machine and should be
scaled suitably.

Marking
scheme

Assessment
items

Project
plan 10% Week 3

You
must show that you have done some preliminary research on this
design. You should show some calculations of the forces and torque
experienced in the design. You must also specify how you plan to
allocate work and who is going to do what. There should be schedule
for a pathway to completion.

Interim
report 20% week 6

This
report should consist of all design topics that were covered until
Week 5 (until Rivets and Welding). This should clearly tell which of
you did what part of the design. One may submit a more extensive
design too. The report should as a minimum cover CAD drawing and
animation of a gear box attached to a motor. You should also provide
clear evidence of your interaction with your team members and your
contributions to the team. You should mention how you provided your
individual portion on time, how you helped your team members, and
minutes of each meeting that you attend. You will need to submit
records of your meeting with all submissions.

Marking
guidelines for Interim report – 20 marks Week 6

Area
of report
85-100% 75-84% 65-74% 50-64% 40-49% <40%
Individual
contribution 65%
Very
good progress shown in the report and covers all the design
topics until Week 5. The design of gear box is complete with
animation using the CAD package.
Good
progress shown in the report and covers most aspects of the
design topics until Week 5. The design of gear box is complete
with animation using the CAD package.
Good
progress shown in the report and covers only some aspects of the
design topics until Week 5. The design of gear box is complete
with animation using the CAD package.
Fair
progress shown in the report and covers some aspects of the
design. The design of gear box is partially complete using the
CAD package.
Some
progress shown in the report and covers very few aspects of the
design. The design of gear box is partially complete. No work
using CAD package.
Poor
progress shown in the report and covers very few aspects of the
design. The design of gear box is incomplete. No work using CAD
package.
Group
report 25%
The
report is excellent and covers all aspects of the design until
Week 5. The report is written very fluently, and the report flows
very well. The report is well written and shows contribution of
each student in the group.
The
report is very good and covers all aspects of the design until
week 5. The report is written very fluently, and the report flows
very well. The report is well written and shows contribution of
each student in the group.
The
report is written good and covers all aspects of the design until
week 5. The report is written fluently, and the report flows
well. The report is well written and shows contribution of each
student in the group.
The
report is written fairly well and covers some aspects of the
design until week 5. The report is written fluently, and the
report flows well. The report does not clearly show the
contribution of each student in the group.
The
report is written good and covers a few aspects of the design
until week 5. The report is written fluently, and the report
flows well. The report does not clearly show the contribution of
each student in the group.
The
report is written good and covers a few aspects of the design
until week 5. The report is written fluently, and the report
flows well. The report does not clearly show the contribution of
each student in the group.
Teamwork
contribution 10%
Contributions
towards organising and correcting report and other aspects of
project
Clear
evidence of strong leadership and initiative in group’s
activities. Strong evidence of collaboration. Strong evidence of
contributions to the report development and organization.

Clear
evidence of leadership and initiative in group’s activities.
Clear evidence of collaboration. Clear evidence of contributions
to the report development and organization.
Evidence
of sufficient leadership and initiative in group’s activities.
Evidence of sufficient level of collaboration. Evidence of
contributions to the report development and organization
Evidence
of adequate leadership and initiative in group’s activities.
Evidence of adequate level of collaboration. Evidence of
contributions to the report development and organization.
Insufficient
evidence of leadership and initiative in group’s activities.
Insufficient evidence of adequate level of collaboration.
Insufficient evidence of contributions to the report development
and organization.
Little
or no evidence of leadership and initiative in group’s
activities. Little or no evidence of collaboration. Little or no
evidence of contributions to the report development and
organization.

Presentation
30% Week 9 Poster produced on a slide (A1 size) and oral presentation
– 3 minutes (individual) + 1000-word report

Marking
guidelines for Presentation and report – 30 marks Week 9

Area
of report
85-100% 75-84% 65-74% 50-64% 40-49% <40%
Individual
presentation 45%. You must do a oral presentation of your part.
Very
good fluent presentation and very good progress shown in the
report and covers all the design topics until Week 8.

Good
fluent presentation and Good progress shown in the report and
covers most aspects of the design topics until Week 8.

Good
fluent presentation and Good progress shown in the report and
covers only some aspects of the design topics until Week 8.

Fairly
fluent presentation and fair progress shown in the report and
covers some aspects of the design.

Some
fluency in presentation and some progress shown in the report and
covers very few aspects of the design..

Poor
presentation and poor progress shown in the report and covers
very few aspects of the design. The design of gear box is
incomplete. No work using CAD package.
Group
report 45%
The
report is excellent and covers all aspects of the design until
Week 8. The report is written very fluently, and the report flows
very well. The report is well written and shows contribution of
each student in the group.
The
report is very good and covers all aspects of the design until
week 8. The report is written very fluently, and the report flows
very well. The report is well written and shows contribution of
each student in the group.
The
report is written good and covers all aspects of the design until
week 8. The report is written fluently, and the report flows
well. The report is well written and shows contribution of each
student in the group.
The
report is written fairly well and covers some aspects of the
design until week 8. The report is written fluently, and the
report flows well. The report does not clearly show the
contribution of each student in the group.
The
report is written good and covers a few aspects of the design
until week 8. The report is written fluently, and the report
flows well. The report does not clearly show the contribution of
each student in the group.
The
report is written good and covers a few aspects of the design
until week 8. The report is written fluently, and the report
flows well. The report does not clearly show the contribution of
each student in the group.
Teamwork
contribution 10%
Contributions
towards organising and correcting report and other aspects of
project
Clear
evidence of strong leadership and initiative in group’s
activities. Strong evidence of collaboration. Strong evidence of
contributions to the report development and organization.

Clear
evidence of leadership and initiative in group’s activities.
Clear evidence of collaboration. Clear evidence of contributions
to the report development and organization.
Evidence
of sufficient leadership and initiative in group’s activities.
Evidence of sufficient level of collaboration. Evidence of
contributions to the report development and organization
Evidence
of adequate leadership and initiative in group’s activities.
Evidence of adequate level of collaboration. Evidence of
contributions to the report development and organization.
Insufficient
evidence of leadership and initiative in group’s activities.
Insufficient evidence of adequate level of collaboration.
Insufficient evidence of contributions to the report development
and organization.
Little
or no evidence of leadership and initiative in group’s
activities. Little or no evidence of collaboration. Little or no
evidence of contributions to the report development and
organization.
ENG338
Machine Design Principles – Detailed Design
Marking guidelines
 –
FINAL
REPORT 40 marks
Area
of report and value
 
85
– 100%
 
75
– 84%
 
65
– 74%
 
50
– 64%
 
40
– 49%
 
<
40%
 
Design
calculations and Report structure, fluency and accuracy 
 
40%

Design
is based on equations from text book appropriately
referenced. Appropriate materials selection and properties,
safety factors considered. Layout and structure of the
report is excellent with document having clear and logical flow
from section to section. The document is very easy to follow with
fluent sentences, free of punctuation and spelling errors.
Subject specific vocabulary confidently used. Design is
fully in SI units. All specs are met. All aspects of
the machine and the design specifications for each machine
element are covered.  
The
design is clearly described with the aid of appropriate
diagrams. Industry Standards
are followed. Design based on costings, modularity,
sustainability and maintainability.
 
Design
is generally based on equations from text book appropriately
referenced. Appropriate materials selection and properties,
safety factors considered. Layout and structure of the
report is very good with document having clear and logical flow
from section to section. The document is easy to follow with
well-formed sentences, mostly free of punctuation and spelling
errors. Subject specific vocabulary is generally used. Design
is fully in SI units. All specs are met. All aspects of
the machine and the design specifications for each machine
element are covered. The design is clearly described with
the aid of appropriate diagrams. Design
based on costings, modularity, sustainability and
maintainability.
 
Design
is generally based on equations from text book and, at times,
appropriately referenced. Appropriate materials selection
and properties, safety factors considered. Layout and
structure of the report makes document readable and accessible.
Flow is mostly logical. The flow from section to section can be
improved.
Some
successful use of subject specific vocabulary. Design is
fully in SI units. All aspects of the machine and some
of the design specifications for each machine element
are covered.  Some
mention of costings, modularity, sustainability and
maintainability.
The
design is clearly described with the aid of appropriate
diagrams. 
 
Design
is generally based on equations from text book and, not
appropriately referenced. Some flaws in presentation. 
Adequate
materials selection and properties, safety factors
considered. Structure and layout interfere with clarity and
readability. 
Some
grammatical, spelling, and punctuation inaccuracies. 
Word
choice and use of subject specific vocabulary unsure. Design
is not fully in SI units. All aspects of the
machine and some of the design specifications for
each machine element are covered.  
The
design is described with the aid of appropriate diagrams. 
 
Inadequate
coverage of design calculations. Failure to present or to
control different sections of the report.  
Many
inaccuracies of grammar and/or punctuation and/or spelling and
calculations. 
Limited
vocabulary. Design is not fully in SI units. Design
specs poorly met. Inappropriate materials selection and
properties, safety factors considered. 
Very
poor design with references to equations. Structure detracts
from understanding. 
Numerous
mistakes in spelling and grammar and calculations. Design
is not fully in SI units. No understanding of how specs
are to be met. Inappropriate materials selection
and properties, safety factors considered. 
CAD
drawing  
(25%) 
Clear
and comprehensive CAD drawings. Demonstrates excellent
understanding of methods used by CAD software. Each machine
element can be seen as a part and as assembly.  
Clear
and complete CAD drawings. Demonstrates very
good understanding of methods used by CAD software.
Each machine element can be seen as a part and as assembly. 
Clear
depiction using CAD drawings. Demonstrates good understanding
of methods used by CAD software. Each machine element can be
seen as a part and as assembly. 
Adequate CAD
drawings. Demonstrates fair understanding of
methods used by CAD software. Each machine element can be
seen as a part and as assembly. 
Inadequate CAD
drawings. Demonstrates poor understanding of
methods used by CAD software. Each machine element cannot be
seen as a part and as assembly. 
Inadequate CAD
drawings. Demonstrates very poor understanding of
methods used by CAD software. Each machine element cannot be
seen as a part and as assembly. 
Animation
(10%) 
Clear
and detailed animation that can be broken in to several
sub-assemblies. All the different machine elements can be easily
seen to be working together. 
Clear animation
that can be broken in to several sub-assemblies.  All the
different machine elements can be easily seen to be working
together. 
Clear
animation that can be broken in to several sub-assemblies. 
All the different machine elements can be fairly seen to be
working together. 
Animation
shows that demonstrating some control over the CAD software.
Sub-assemblies are not very clear. 
Poor
animation with little demonstration of CAD software. No
subassemblies seen 
Unclear
or no animation. 
3D
printing of machine  
15%) 
Clear
and comprehensive 3D printed scaled-down model. Meets the design
specs.  The design is innovative. The design is clearly
described with different coloured parts. 
Very
good 3D printed scaled-down model. Meets the design specs. 
The design is very good.   The design is clearly
described with different coloured parts. 
Good 3D
printed scaled-down model. Meets the design specs.  The
design is good.   
Adequate 3D
printed scaled-down model. Meets some of design specs.  The
design is fair. 
Incomplete 3D
printed scaled-down model. Some design specs not met.  The
design is poor. 
Incomplete 3D
printed scaled-down model. Design specs not met.  The design
is very poor. 
 Teamwork
contribution 10%
Contributions
towards organising and correcting report and other aspects of
project
Clear
evidence of strong leadership and initiative in group’s
activities. Strong evidence of collaboration. Strong evidence of
contributions to the report development and organization.

Clear
evidence of leadership and initiative in group’s activities.
Clear evidence of collaboration. Clear evidence of contributions
to the report development and organization.
Evidence
of sufficient leadership and initiative in group’s activities.
Evidence of sufficient level of collaboration. Evidence of
contributions to the report development and organization
Evidence
of adequate leadership and initiative in group’s activities.
Evidence of adequate level of collaboration. Evidence of
contributions to the report development and organization.
Insufficient
evidence of leadership and initiative in group’s activities.
Insufficient evidence of adequate level of collaboration.
Insufficient evidence of contributions to the report development
and organization.
Little
or no evidence of leadership and initiative in group’s
activities. Little or no evidence of collaboration. Little or no
evidence of contributions to the report development and
organization.

The post Design Assignment appeared first on My Assignment Online.

Plagiarism Free Assignment Help

Expert Help With This Assignment — On Your Terms

✓ Native UK, USA & Australia writers ✓ Deadline from 3 hours ✓ 100% Plagiarism-Free — Turnitin included ✓ Unlimited free revisions ✓ Free to submit — compare quotes

admin

Academic writer and editor at BestWriters.

Get your paper off your plate tonight

Post your instructions for free. Prices start at $5 per page.

Place an order