Introduction
In structural design and construction materials, the choice of a material in any part of the construction is anchored on the properties based on the required task. Steel is one of the building materials used in structural engineering with properties such as strength for durability and ability to withstand external forces amongst other properties. In this work, steel is reviewed as a construction material based on the questions attached.
- A simply supported beam spans 6m and has uniformly distributed factored actions of 125 N/m applied over its full length. The beam is fully restrained on its top flange by a 150 mm thick reinforced concrete slab.
- Calculate the bending moment and shear force, design values
Bending moment is given as the product of force multiplied by the perpendicular distance from point of support to the line of action of force as follows;
However, with factored action known, the bending moment can be given by;
= 125 * 6
= 750Nm
Shear force on the other hand is given as a function comprising of the product of the cross sectional area and total force, hence;
= 750 * 6*0.15
= 675 N
- Size the steel preliminarily
Assume that the steel is 6 m long and it perfectly match on the concrete slab hence it must be 150 mm thick as well.
- Calculate the cross-section classification of the assumed steel section
The cross sectional area = Length x width
= 6 x 0.15
= 9 m2
- Check the bending and shear resistance of the section
Bending resistance = Force/Cross section area
= 675/9
=75
- State whether the section is adequate or not
Based on the bending resistance value as compared to the value of Young’s modulus, the structure as it is cannot be adequate as a section for construction
- Section Design
A fully lateral restrained 457x191x98 UB section is designed to carry a combined major axis bending movement and an axial force. Grade of steel is S275.
You are required to:
- Calculate and determine the cross-section classification under pure compression
Under the constrains of pure compression, the cross sectional area must be as large as possible to enable the material to operate below the yield stress. In addition, the structure is laterally placed hence the cross sectional area is given by the two dimensions of corresponding larger sizes.
Thus, A = L x W
= 82717 m2
- Determine the maximum bending moment that can be carried by this 457x191x98 UB section in the presence of an axial force of 400kN
Yield strength for a material is defined according to Inoue et al., (2017), as the materials’ stress for which it begins to yield to the deforming force. For steel S275, the yield stress is given equal to 275.
Materials’ stress = Deforming force / Cross sectional area
In this case, the deforming force is given by the compressional force, hence the maximum bending moment will be corresponding to the stress at minimum area.
Minimum area = 191 x 98
= 18718 m2
The maximum bending moment is thus given by;
Bending moment = 400000 x 457
= 182.8 MN
- Embrace creative design or think out-of-the box
The local city council is seeking to have a new pedestrian bridge linking the A4150 and the local transport police station. This will transform the riverside environment and create a new opportunity for residential and commercial investment, which may build confidence in future growth. You need to present Three different solution based on the following essential priorities or drivers. You need to consider one of these priorities each time; cost, aesthetic and buildability.
Project brief
Based on the analysis of the situation, the required bridge will bring more good than otherwise especially when constructed in a way that offers both durability and aesthetic values. For a greater good to be derived from the project, it is important to ensure that the project outcome creates an environment that fosters commercial activities and hence meeting the future requirements of the dependents (Wen et al., 2015). To some extent, a number of people, bearing in mind the expenses to be incurred, may tend to think that the project will not be viable. Indeed, there will be some cost involved in this project but that is nothing comparable to the unseen cost incurred by people who have to get into the station since they are compelled to move far around in order seek entrance (Tsai et al., 1993). In a similar way, cost analysis can also be anchored on the type of the materials used. Stronger and durable materials like steel are expensive to use in the initial run but they have proven to be the cheapest in the final long term run.
Outline specification
In this project, the proposed material usage will be steel and concrete for the following reasons. Both steel and concrete have the same rate of linear expansion and therefore will contract and expand at virtually the same rates. The differing rates of linear expansion and construction have always been the source of structural deformation that brings many structures down despite the initial cost of the structures. Similarly, steel is a stronger material with very high resilience to deforming forces especially the working loads. The high resilience will imply that the material will correspondingly have very high tensile and yield strength which then requires very high working load to bring the structure down (Wen et al., 2015). As a consequence, the safety factor of the material combination in the proposed structure will be within the required standards. Nonetheless, safety factor for structures will also depend on the workmanship of the structure and not merely on the material selection. For each dimension of the steel and other structures in a particular usage within the whole structure, necessary tests such as buckling, yield, elasticity as well as stress and strain relation will be conducted well in advance.
Conclusion
The choice of the material used in erecting a given structure is of great importance in the field of construction engineering. While the material strength and its long term dependability if not only a factor of material choice, the proposal for building structures is greatly anchored on the material choices and corresponding material costs. This work proposes a combination of concrete and steel in erecting the bridge based on the materials strength, dependability, resilience amongst many other outstanding properties as compared to any other material choices available for the construction. Though cost of the project may appear to be comparatively higher especially when comparison is based on the alternative material choice, it is believed that at final long run, the proposed material choices will be the best.
References
Inoue, N., Yonezu, A., Watanabe, Y., Yamamura, H. and Xu, B., 2017. Prediction of Asymmetric Yield Strengths of Polymeric Materials at Tension and Compression Using Spherical Indentation. Journal of Engineering Materials and Technology, 139(2), p.021002.
Tsai, Keh-Chyuan, Huan-Wei Chen, Ching-Ping Hong, and Yung-Feng Su. “Design of steel triangular plate energy absorbers for seismic-resistant construction.” Earthquake spectra 9, no. 3 (1993): 505-528.
Wen, T.J., Siong, H.C. and Noor, Z.Z., 2015. Assessment of embodied energy and global warming potential of building construction using life cycle analysis approach: Case studies of residential buildings in Iskandar Malaysia. Energy and Buildings, 93, pp.295-302.
The post Design Studies Answered Assignment appeared first on My Assignment Online.