- Introduction
(This section is approximately 1 – 2 pages)
Introduce the reader to the project. What is the project based on, what is the problem to be solved etc (2-3 paragraphs).
Outline the goals of the project. For example:
- Design and build a system that can measure the voltage and current supplied to a battery by a charge controller driven by a PV panel
- Use the system to calculate various PV performance metrics such as power generated and energy delivered to the battery
- Display these metrics on an LCD screen in real-time
- Log these metrics over time to a storage device for future analysis
The finishing paragraph of this chapter should lead into the next chapter.
- Background
(This chapter is approximately 8 – 10 pages)
The aim of this chapter is to provide background to the project. It presents an overview of what is already known about the subject. This is often called a Literature Review. It is important that this chapter is well-referenced to ensure the validity of the information.
- Solar Energy
Solar energy is a term used to describe ……
The following sections describe the principles, operation, applications and components of a solar energy system.
- Solar Energy Overview
This section describes what is meant by solar energy and what it is used for.
- PV Panel Operation
This section describes how PV panels are constructed and how they work. It could include:
- PV cell
- Connection of multiple PV cells (series/parallel)
- Operation as a current source
- Key parameters (short-circuit current, open-circuit voltage)
- The I/V curve
Sometimes it helps to summarise information using a table, such as Table 2 -1. Note that the table number here is a hyperlink: clicking on the table number brings you directly to the table. This is achieved using a cross-reference, which is explained at the end of this section.
Tables can be created by clicking the Insert menu and selecting ‘Table’, followed by ‘Insert Table’. The number of rows and columns can then be selected.
Once the table has been created, a caption can be added by selecting the table, right-clicking on the table control symbol in the top left corner, and selecting ‘Insert Caption’. Table captions should be above the table, so for ‘Position’ choose ‘Above selected item’. To include chapter numbers in table number, click on ‘Numbering’ and check the ‘Include chapter numbers’ checkbox. Table captions should also be centred, so highlight the caption and, under the ‘Home’ menu and the ‘Paragraph’ ribbon, click the ‘Center’ icon.
Tables can be referenced from your word document using the cross-reference feature. To do this, place the cursor where you want the reference (for example, Table 2-1) to be added. Under the ‘Insert’ menu, select ‘Cross-reference’. Under ‘Reference type’ select ‘Table’, and under ‘Insert reference to’ select ‘Only label and number’. This will bring up a list of all possible tables; select the table from the list and click ‘Insert’ to insert the reference in your text. By checking the ‘Insert as hyperlink’ checkbox, the reference in your text will act as a hyperlink. This is especially useful if you are referring to a table in another part of your document, because clicking on the reference will bring you to the table.
Table 2‑1: Important PV Parameters
| Parameter | Symbol | Unit | Description |
| MPP power | PMPP | WP | Maximum power under STC (nominal power) |
| Efficiency | η | % | Ratio of the power delivered by the cell and the solar irradiance |
| Fill factor | FF | – | Quality yardstick for solar cells, generally between 0.5 and 0.85 |
| MPP voltage | VMPP | V | PV voltage at MPP |
| Open-circuit voltage | VOC | V | Voltage the solar cells supplies when neither terminal is connected to a load |
| MPP current | IMPP | A | PV current at MPP |
| Short-circuit current | ISC | A | Current the solar cell provides when both terminals are directly connected |
- PV System
This section presents the components of a PV system and how they are connected together. Such components are illustrated in Figure 2 -1.
Figures may be added to a Word document by clicking the Insert menu, selecting ‘Pictures’ and browsing to the location of the image file. Captions and cross-references are added as for a table. Captions should be placed below the figure and should be left-justified.
Figure 2‑1: Components of a PV system
- Charge Controller
This section discusses the purpose and operation of a charge controller.
- Battery
This section discusses the purpose and key parameters of a battery in a PV system.
- Arduino
An Arduino Teensy 3.6 microcontroller to measure the voltage and current from sensors connected to the battery, and calculate power and energy delivered to the battery. The data will be displayed on an external LCD screen and will be logged to the Arduino’s SD card. The following sections introduce the Arduino and discuss the functionality that will be used in this project.
- Arduino Overview
This section gives an overview of the Arduino Teensy 3.6. Ideally it should include a picture and a pinout.
- Analog-to-Digital Converter
Both the voltage and current sensors output a voltage that is proportional to the battery voltage and current. This voltage is converted to a digital number using the Arduino’s analog-to-digital converter (ADC). An overview of how ADCs operate is presented in this section. Key parameters such as ADC resolution are also discussed.
- Digital Communication
The Arduino will control the LCD screen over I2C. This section gives a brief outline of the I2C protocol.
- Project Plan
(This chapter is approximately 4 pages)
The aim of this chapter is to outline the initial planning of the project. It can include:
Figure 2,mind map
- Concept proposal
- Brainstorming of ideas – mind map
- Preliminary design
The post Important PV Parameters appeared first on My Assignment Online.