Limited Offer Get 25% off — use code BESTW25
No AI No Plagiarism On-Time Delivery Free Revisions
Claim Now
Prices start at $5 per page · plagiarism-free papers · free revisions for 14 days 24/7 support: support@bestwriters.com
Uncategorized

Lab 2 Measuring Motor Performance (Part 1)

  • Posted
  • Authoradmin
  • Length710 words
  • Reading time4 min
Write My Assignment FREE

Introduction
As a motor skills practitioner (physical education teacher, movement therapist, athletic coach etc.), it is import to use performance measures to make assessments. This requires determining which aspects of a performance to measure to make a valid assessment, and then determining how to measure the aspects of interest. In this class, we will collect simple two-dimensional (2D) kinematics and physiological data related to cycling performance under three coordination conditions. This will give students experience with conducting movement data collection and will form the basis of a later class where simple movement measures, such as joint angles, will be extracted from the collected data.
Methods
Equipment
 Watt bikes x 3 (pedals: in-phase 0°, anti-phase 180°, out-of-phase 90°, see Figure 2.1 below)
 Smart phones with slow motion function x 2
 Smart phone tripods x 2
 Metabolic system x 1
 Consumables
o Masking tape
o Large marker pen
Figure 2.1: Three pedal coordination conditions.
Procedure

Place joint markers on participant (left and right lower limb, see Bony Landmark Joint Marker section below)

Set smart phone to slow motion video recording (120 Hz (frames/s) is preferred)

Attach smart phones to tripods

Adjust bike seat height for participant

Position smart phones on either side of the Watt bike (perpendicular to the participant’s sagittal plane). Make sure the joint makers are clearly visible by the smart phones throughout the whole cycle action.

Initiate and prepare participant with metabolic measurement system*
9

Randomly select a coordination condition

While collecting metabolic data, have the participant pedal at ~ 70 watts (resistance ≈ 3.5, rpm ≈ 50) for 3 minutes

During the last minute, collect ~ 30 s of kinematic video data

Repeat steps 7 – 9 with the remaining two conditions

Save video clips for later analysis
*Note: Collecting metabolic data is not a learning objective for EHR214 and the tutor will operate this equipment. Results will be discussed at a later lecture.
Bony Landmark Joint Markers
Using a marker pen and masking tape, make markers by drawing large black dots on pieces of masking tape (dots should be about the size of a 20 cent coin). Place these markers on your participant at the appropriate body landmarks for your trial as indicated below (i.e. upper body for throwing activities, lower body for walking/running & kicking type activities, see Figure 2.2 below)
Figure 2.2: Bony landmark marker placement
10
Lab 3 Working Memory
Introduction
Memory is the capacity that permits organisms to benefit from past experiences. The functions of memory include storage of information, retrieval of information and other specific functions in these components e.g. problem solving. Memory structure is divided into two functional systems, working memory and long-term memory. Whist the capacity of long-term memory is relatively unlimited, working memory is confined by certain limitations e.g. individuals can store approximately 7 (+/- 2) items in their working memory and begin to lose information following 20-30 sec. The significance of memory is that it allows us to recall previous motor skill experiences and use this information make more informed movement decisions and guide motor pattern selection during performance during subsequent motor skill situations.
Purpose
The purpose of this class is to demonstrate the capacity of working memory and understand the mechanisms for improvement.
Equipment
 Working memory presentation
Procedure
You will perform a memory test involving recalling numbers in a correct sequence. The numbers are shown to you one at a time. Once all the numbers in the sequence have been shown, you will be asked to recall these numbers in the correct order. This is to be completed in the tables below.
You will perform this test under two conditions. First, you will tested so that you have to recall a 5 number sequence. Second, you will tested again but now be asked to recall a 9 number sequence. There are 20 trials of each number sequence that need to be recalled.

Questions

  1. Do your results fit with the capacity of working memory?



  1. How do the results fit in with the notion of primacy and recency effects?



  1. What strategies might participants use to remember the sequence?



  1. What is the term used to describe the interference that occurred and how do your results fit in with this notion? Give an example of how these might have occurred.




  1. What is a real-world application of these results?



The post Lab 2 Measuring Motor Performance (Part 1) appeared first on My Assignment Online.

Plagiarism Free Assignment Help

Expert Help With This Assignment — On Your Terms

✓ Native UK, USA & Australia writers ✓ Deadline from 3 hours ✓ 100% Plagiarism-Free — Turnitin included ✓ Unlimited free revisions ✓ Free to submit — compare quotes

admin

Academic writer and editor at BestWriters.

Get your paper off your plate tonight

Post your instructions for free. Prices start at $5 per page.

Place an order