Contents

Project Scope and Goals 2

Project requirements(Hardware & Software) 2

Detailed Network Design in Packet Tracer which includes 3

Network device configurations 4

Switch configuration: 4

Create VLAN 4

Ping each other 5

Set VTP domain with your first name 5

Set VTP password with your family name 6

Demonstrate VTP packets 6

Router configuration 6

Set descriptions on interfaces, one with your name, second with your family name, third with your middle name 6

Display information about directly connected devices to router 7

Setup IP addresses for each interface. 7

What is the subnet mask did you use? 7

Ping all routers. 8

References 8

Project Scope and Goals

As per the requirements for the network of University of Future Technology in Australia, we have planned to implement the network with below mentioned scope. The scope of this project is very specific, and they are as below.

1. Enable WAN connection between two campuses in different ends of city with same structure.
2. Enable network connectivity throughout their lecture theatres, Labs, Faculty area, Administration Office, and student service areas in both campuses.
3. Provide Wi-Fi access for students
4. Provide Internet access for students
5. Segmentation of the network between student, faculty and administration domains.

Project requirements(Hardware & Software)

Device Type	Model
Workgroup Switch – 48 Port	Cisco WS-C2960S-48TS
Workgroup Switch – 24 Port	Cisco WS-C2960S-24TS
Router	Cisco C1921-3G-V-K9
Access Points	Cisco AIR-CAP3602E-A-K9
PC	HP Elitedesk G4
Laptop	HP Elitebook G5

Detailed Network Design in Packet Tracer which includes

Detailed Network Design in Packet Tracer which includes

All switches

All routers

VLAN

VTP

All PCs

VLAN	Description	Hosts	Network Address
VLAN 10	VLAN for Students	510	10.10.0.0/23
VLAN 20	VLAN for Faculty	510	10.10.2.0/23
VLAN 30	VLAN for Administration	510	10.10.4.0/23
VLAN 40	VLAN for WLAN	510	10.10.6.0/23

Network device configurations

Switch configuration:

• Set IP addresses on PC and switch
• Switch_A>ena
  Switch_A#conf t
  Switch_A(config)#interface vlan 1
  Switch_A(config-if)#ip address 10.1.2.2  255.255.255.0
  Switch_A(config-if)#no shut
  
  Switch_B>ena
  Switch_B#conf t
  Switch_B(config)#interface vlan 1
  Switch_B(config-if)#ip address 10.1.2.3 255.255.255.0
  Switch_B(config-if)#no shut
  
  Switch_C>enable
  Switch_C#configure terminal
  Switch_C(config)#interface vlan 1
  Switch_C(config-if)#ip address 10.1.2.4 255.255.255.0
  Switch_C(config-if)#no shut

Create VLAN

Switch(config)#vlan 10

Switch(config-vlan)#name student

Switch(config-vlan)#vlan 20

Switch(config-vlan)#name faculty

Switch(config-vlan)#name 30

Switch(config-vlan)#name admin

Switch(config-vlan)#name 40

Switch(config-vlan)#name WLAN

Ping each other

Set VTP domain with your first name

Switch_A(config)#vtp domain AKHLAQ

Set VTP password with your family name

Switch_A(config)#vtp password Ahmad

Demonstrate VTP packets

Router configuration

Set descriptions on interfaces, one with your name, second with your family name, third with your middle name

Display information about directly connected devices to router

Setup IP addresses for each interface.

What is the subnet mask did you use?

For Serial interfaces 255.255.255.252

For Gigabit Ethernet Sub interfaces 255.255.254.0

Ping all routers.

References

[1]”Configuring VLAN Trunk Protocol (VTP)”, Cisco, 2020. [Online]. Available: https://www.cisco.com/c/en/us/support/docs/lan-switching/vtp/98154-conf-vlan.html. [Accessed: 26- May- 2020].

[2]”Small Business Solutions – IT Products and Services”, Cisco, 2020. [Online]. Available: https://www.cisco.com/c/en_in/solutions/small-business.html?DTID=pseggl000015&CCID=cc000260&OID=0&Country_Site=IN&Campaign=SMB-02&Creative=&CCID=cc000260&OID=0&Country_Site=IN&Campaign=SMB-02&Creative=IN_SEM_SMB_Q3FY20-mobile-T2-Cisco-Start-Wireless_BMM_NB_DD-GGL_0_Small-Employer_Observation_Eng&REFERINGSITE=google&keyword=%2Baccess%20%2Bpoints&kwid=%7bdskeywordid%7d&ccid=&dtid=&oid=&POSITION=SEM&COUNTRY_SITE=&CAMPAIGN=&CREATIVE=&REFERRING_SITE=Google&KEYWORD=%2Baccess%20%2Bpoints&gclid=CjwKCAjw2a32BRBXEiwAUcugiE9tW1fly_LdXo3eygjBDtowoMPv9rjWHXY0dqn6VjlAKblSff4GlRoCjJgQAvD_BwE&gclsrc=aw.ds#~stickynav=1. [Accessed: 26- May- 2020].

[3]”HP Desktop Pro A G3 Specifications | HP® Customer Support”, Support.hp.com, 2020. [Online]. Available: https://support.hp.com/sg-en/document/c06522206. [Accessed: 26- May- 2020].

The post Project Scope and Goals appeared first on My Assignment Online.